Synthetic Roofs

We sell a variety of snow guards and roof snow retention devices specifically made for asphalt shingle roofs and synthetic shingle roofs, either for new construction or on existing roofs (retrofit). We have the largest selection of snowguards and rails on the internet!


Items: 115 of 24, per page
Drop items here to shop
Product has been added to your cart
  • Drag and drop me to the cart

    Aluminum or bronze, select below. For slate and asphalt shingle roofs. Heavy strap with three mounting holes. 9.5 inches long overall, 5 5/8 inch wing span width, 4.5 inches high. 

    We can paint our Jalco aluminum snow guards in almost any color, upon request, for an additional charge! 

    Jalco Snow Guards have been designed to prevent snow slides. After years of  installing slate roofs with steel snow guards with resulting rust trails  going down the roofs, John Kleckner designed snow guard to eliminate this unsightly problem. In 1958 he came out with what was  arguably the first aluminum snow guard. Jalco aluminum snow guard castings are made with at least 50% recycled aluminum.

    • $6.95

    Not rated yet
  • Drag and drop me to the cart

    Heavy aluminum strap with three mounting holes. 9.5 inches long overall, 5 3/4 inch width, 2 3/4 inches high. 

    We can paint our Jalco aluminum snow guards in almost any color, upon request, for an additional charge!

    Aluminum or bronze - select below.

    • $6.30

    Not rated yet
  • Drag and drop me to the cart
    Designed to be installed on slate by nail application (#100S-NA) or asphalt shingle roofs (#100S-AS) during the installation of the roofing. All BRONZE GUARD® products are cast in pure tin bronze, using only virgin metals to assure the highest quality alloy. Select below: Slate application or Asphalt application.


    A  traditional spike style snow guard, from a design first patented in 1899. The Model #100 is historically accurate for period restorations, but is just as appropriate for new construction or retrofit application on existing slate roofs. Because of its low profile, this model is more appropriate for residential usage. The Model #100 is for applications on slate, shake, and shingle roofs, and is designed to fit between adjacent pieces of roof material, so that only the casting is visible  above the roof surface.


    This snow guard is also available in a retrohook style for installing on existing slate roofs.

    The #100 snowguard has a smaller face than the #200, and is less expensive. View the 200 standard.


    • $13.50

    Not rated yet
  • Drag and drop me to the cart

    For slate roofs and asphalt shingle roofs. Heavy aluminum strap with three mounting holes. 9.5 inches long overall, 4 3/4 inch wing span width, 4.5 inches high, 9.8 ounces.

    This is a solid snowguard with a full Eagle figure on both the  front and the back of the snowguard (not hollow on the back side).

    We can paint our Jalco aluminum snow guards in almost any color, upon request, for an additional charge!

    • $7.50

    Not rated yet
  • Drag and drop me to the cart
    Designed to be installed on slate roofs (#200S-NA) or asphalt shingle roofs (#200S-AS) during the installation of the shingles. Select type below. The Mullane #100 snowguard has a smaller face than the Mullane #200.


    This  spike style snow guard is fabricated from the same sheet metal  components as the #100, but the #200 casting is 30% larger than the  #100. Both products are equally strong and effective in their capacity  to hold snow on the roof, but the Model #200S is more appropriate to  larger scale buildings, or where the roof material is thicker than  usual, such as tile roofing.

    All BRONZE  GUARD® products are cast in pure tin bronze, using only virgin metals to  assure the highest quality alloy. The castings are produced locally by  old-world craftsmen using state of the art equipment to assure that each  casting is of consistent quality. The final assembly is done by hand,  using only solid copper rivets, so that each finished product is of  uniform quality.

    The #200 snow guard is also available in a retrohook style for installation on existing slate roofs.

    • $14.00

    Not rated yet
  • Drag and drop me to the cart
    Berger Brothers Model #SG2 heavy duty snow guard available in bronze (SGBR2) or galvanized iron (SGML2). Five inches wide, 2 3/4 inches high. The riveted bar is 1/8 inches x 1 inch x 12 inches long and goes 8 inches under the slate. When installing, the underlying slate is notched to allow for the snow guard strap. 

    These snow guards are also suited for wood shake, tile, and mineral surfaced  shingles. Excellent in areas that receive heavy snows! This snow guard is to be installed during the slate roof installation - it is not a retrofit model.

    Snow guards should be installed where the potential for the sudden sliding of ice and snow can be hazardous to people or property below. Falling snow is a life safety issue, and careful consideration of liability issues should be part of a carefully designed roof system in all areas prone to winter snow and ice.
    • $11.50

    Not rated yet
  • Drag and drop me to the cart

    Berger Brothers Model #95 heavy duty ornamental snow guard in bronze, aluminum or galvanized iron (select below). A larger guard with Gothic styling designed to transfer snow and ice loads more effectively to reduce cracking of the slate.

    1/8  inches x 1 inch x 12 inch bar in appropriate metal combination.  Excellent in areas that receive heavy snows! This snow guard is to be  installed during the slate roof installation (it is not a retrofit  model).

    Snow  guards should be installed where the potential for the sudden sliding of  ice and snow can be hazardous to people or property below. Falling snow  is a life safety issue, and careful consideration of liability issues  should be part of a carefully designed roof system in all areas prone to  winter snow and ice.


    • $17.00

    Not rated yet
  • Drag and drop me to the cart

    Berger Brothers SGLLC1 copper loop the loop economy snow guard for wood deck applications on newly installed slate roofs, wood shakes or asphalt shingles. By fhe piece, or by the case of 300 (select below).

    The Loop  the Loop snow guard is an economy guard for wood deck applications on newly installed slate roofs, wood shakes or asphalt shingles. Available in copper only. Minimum required quantity for proper installation: 4:12 slope roof use 50 guards per square, 6:12 slope roof use 75 guards per square, and 12:12 slope roof use 150 guards per square. These snow guards nail into place like a slate hook. Made from  heavy gauge solid copper wire. When large quantities of snow guards are needed on a tight budget, these snowguards will do the job.

    Snow  guards should be installed where the potential for the sudden sliding of  ice and snow can be hazardous to people or property below. Falling snow  is a life safety issue, and careful consideration of liability issues  should be part of a carefully designed roof system in all areas prone to  winter snow and ice.

    • $2.55

    Not rated yet
  • Drag and drop me to the cart

    Copper or aluminum snowguard for installation on all NEW Synthetic Shingle, Slate, and Shake Materials. (NOTE: NOT for use with DaVinci Bellaforte products. Please see the ST11 model.)


    Clip Style Snow Guard

    • Length: 18 Inches
    • Width: 2 3/8 Inches


    Designed to be installed on NEW:

    • Cedar Shake and Shingle
    • Synthetic Slate and Shake
    • Natural Slate


    Available in:

    • Copper (all snow guard components are 16 ounce copper)
    • Kynar-Coated Aluminum in Liberty Gray or Dark Bronze (all snow guard components are .032 aluminum)
    • Powder  Coated Aluminum. There is a $2.00 per snow guard charge for the powder coating. See color chart below. You will need to call (814) 786-9085 to  order specific color. Lead time for powder coating and fabrication is  approximately 2 weeks.


    • $5.75

    Not rated yet
  • Drag and drop me to the cart

    A copper, or steel snow guard designed for new installations on slate, fake slate, and shake roofs. Typically, snow guards ST11RG10, and RG16 are kept in stock and will ship within 48 hours from processing. If it's not in stock the average lead time is 2 weeks.

    • Length: 16 Inches
    • Width: 1 3/4 Inches


    Designed for new installations on:

    • Cedar Shake and Shingle
    • Synthetic Slate and Shake
    • Natural Slate


    Available in:

    • Copper (all snow guard components are 16 ounce copper)
    • Powder Coated EG Steel. We keep Liberty Gray and Dark Bronze in stock. All  other colors will have a longer lead time. Color chart can be seen below. You will need to call us at 814-786-9085 to order a specific color. Lead time for powder coating and  fabrication is approximately 2 weeks.


    We have fasteners for installing snowguards.


    • $6.50

    Not rated yet
  • Drag and drop me to the cart

    Snow Guard designed for use with most materials and new installation with DaVinci Bellaforte products. Typically, snow guards ST11RG10, and RG16 are kept in stock and will ship within 48 hours from processing. If it's not in stock the average lead time is 2 weeks.

    Clip Style Snow Guard

    • Length: 11 Inches
    • Width: 2 3/8 Inches
    • Weight: 3.8 Ounces

    Designed to be installed on:

    • Synthetic Slate and Shake (New and Retrofit)

    Available in:

    • Copper (all snow guard components are 16 ounce copper)
    • Kynar-Coated Aluminum in Liberty Gray or Dark Bronze (all snow guard components are .032 aluminum)
    • Powder  Coated Aluminum. There is a $2.00 per snow guard charge for the powder  coating. See color chart below. You will need to call (814) 786-9085 to order a specific color. Lead time for powder coating and fabrication is approximately 2 weeks.


    • $5.75

    Not rated yet
  • Drag and drop me to the cart

    Snow Guard for use on new and existing asphalt shingle roofs.

    Clip Style Snow Guard

    • Length: 9 Inches
    • Width: 2 3/8 Inches

    Available in:

    • Copper (all snow guard components are 16 ounce copper)
    • Kynar-Coated Aluminum in Liberty Gray or Dark Bronze (all snow guard components are .032 aluminum)
    • Powder Coated Aluminum. There is a $2.00 per snow guard charge for the powder coating. See color chart above. You will need to call (814) 786-9085 to order specific color. Lead time for powder coating and fabrication is approximately 2 weeks.


    • $5.30

    Not rated yet
  • Drag and drop me to the cart

    Snow guard designed for installations on new asphalt and metal shingle roofs. Available in Powder Coated EG Steel and Copper. Typically, snow guards ST11RG10, and RG16 are kept in stock and will ship within 48 hours from processing. If it's not in stock the average lead time is 2 weeks.

    Clip Style Snow Guard

    • Length: 10 1/8 Inches
    • Width: 1 3/4 Inches
    • Height: 2 3/8 Inches
    • Weight: 8.2 Ounces

    Designed for new installations on:

    • Metal Shingle
    • Cedar Shake and Shingle
    • Synthetic Slate and Shake
    • Asphalt Shingle

    Available in:

    • Copper (All snow guard components are 16 ounce copper.) Also in stock.
    • Powder  Coated EG Steel - We keep Liberty  Gray or Dark Bronze in stock. All  other colors will have a longer lead time. Color chart can be seen below. You will need to call (814)  786-9085 to order a specific color. Lead time for powder coating and  fabrication is approximately 2 weeks.

    We have fasteners for installing snowguards.

    • $6.25

    Not rated yet
  • Drag and drop me to the cart

    Model #4C copper snow guard is manufactured using a double thickness of .020 inch cold rolled copper. Designed for installation on new and existing slate, tile, asphalt shingle, and wood shingle roofs. The snow guard hooks over the head of slate or tile without nailing. Snow guards on asphalt and wood shingles require nailing. 

    Weight: 4.0 Ounces

    Height: 1.5 Inches

    Width: 1.5 Inches

    Length: 6.625 Inches

    Reach: 4.125 Inches

    • $7.50

    Not rated yet
  • Zaleski #8TC Terne Coated
    • 22% less
    Drag and drop me to the cart

    Our Model #8TC terne coated snow guard  is manufactured using terne coated (60% tin and 40% lead) stainless steel. Designed for installation on new and existing slate, tile, asphalt shingle, and wood shingle roofs. The  Snow Guard hooks over the head of the slate or tile without nailing.  Snow Guards on asphalt and wood shingles require nailing. 

    Weight: 3.7 Ounces

    Height: 2.5 Inches

    Width: 1.5 Inches

    Length: 6.625 Inches

    Reach: 4.125 Inches

    • $7.00

    Not rated yet
Items: 115 of 24, per page